Trend

Blades that can be rotated in 90 degree increments giving three extra new edges. Dimensions: D=19 mm C=12 mm B=19 mm A=90 degrees OL=52 mm Shank Diameter=1/4 inch Shank Diameter: 1/4 Diameter Metric: 19 Cut Length Metric: 12 Overall Length Metri...

Blades of cutters can be rotated through 180 degrees to give one new cutting edge. Dimensions: D=19 mm C=30 mm B=19 mm A=90 degrees OL=78 mm Shank Diameter=1/2 inch Shank Diameter: 1/2 Diameter Metric: 19 Cut Length Metric: 30 Overall Length M...

Blades of cutters can be rotated through 180 degrees to give one new cutting edge. Dimensions: D=19 mm C=30 mm B=19 mm A=90 degrees OL=70 mm Shank Diameter=1/4 inch Shank Diameter: 1/4 Diameter Metric: 19 Cut Length Metric: 30 Overall Length M...

Two flute mini-trim with guide bearing will profile intricate shapes. Max. 2.0mm trimming. Ideal for acrylic trimming. Dimensions: D=1/4 inch D=6.3 mm C=25.4 mm OL=75 mm B=Fractionally larger than cutter dia mm A=90 degrees Shank Diameter=1/4 inch...

Profiler with shank mounted bearing guides. For use with router mounted above or below a table when following a template. For profiling and rebating applications only. Not for plunge cutting/grooving. A 3mm maximum overlap should be left before...

Profiler with shank mounted bearing guides. For use with router mounted above or below a table when following a template. For profiling and rebating applications only. Not for plunge cutting/grooving. A 3mm maximum overlap should be left before...

Self-guiding cutters for rounding over edges do not require a side fence. They are supplied with two bearings. Use the larger bearing for a round-over. If the cutter is lowered, a top quirk can be produced. A full round/bullnose for stair tre...

Self-guiding cutters for rounding over edges do not require a side fence. They are supplied with two bearings. Use the larger bearing for a round-over. If the cutter is lowered, a top quirk can be produced. A full round/bullnose for stair tre...

Self-guiding cutters for rounding over edges do not require a side fence. They are supplied with two bearings. Use the larger bearing for a round-over. If the cutter is lowered, a top quirk can be produced. A full round/bullnose for stair tre...

Self-guiding cutters for rounding over edges do not require a side fence. They are supplied with two bearings. Use the larger bearing for a round-over. If the cutter is lowered, a top quirk can be produced. A full round/bullnose for stair tre...

Self-guiding cutters for rounding over edges do not require a side fence. They are supplied with two bearings. Use the larger bearing for a round-over. If the cutter is lowered, a top quirk can be produced. A full round/bullnose for stair tre...

Self-guiding cutters for rounding over edges do not require a side fence. They are supplied with two bearings. Use the larger bearing for a round-over. If the cutter is lowered, a top quirk can be produced. A full round/bullnose for stair tre...

Self-guiding cutters for rounding over edges do not require a side fence. They are supplied with two bearings. Use the larger bearing for a round-over. If the cutter is lowered, a top quirk can be produced. A full round/bullnose for stair tre...

Self-guiding cutters for rounding over edges do not require a side fence. They are supplied with two bearings. Use the larger bearing for a round-over. If the cutter is lowered, a top quirk can be produced. A full round/bullnose for stair tre...

Self-guiding cutters for rounding over edges do not require a side fence. They are supplied with two bearings. Use the larger bearing for a round-over. If the cutter is lowered, a top quirk can be produced. A full round/bullnose for stair tre...

Self-guiding cutters for rounding over edges do not require a side fence. They are supplied with two bearings. Use the larger bearing for a round-over. If the cutter is lowered, a top quirk can be produced. A full round/bullnose for stair tre...

Self-guiding cutters for rounding over edges do not require a side fence. They are supplied with two bearings. Use the larger bearing for a round-over. If the cutter is lowered, a top quirk can be produced. A full round/bullnose for stair tre...

Self-guiding cutters for rounding over edges do not require a side fence. They are supplied with two bearings. Use the larger bearing for a round-over. If the cutter is lowered, a top quirk can be produced. A full round/bullnose for stair tre...

Self-guiding cutters for rounding over edges do not require a side fence. They are supplied with two bearings. Use the larger bearing for a round-over. If the cutter is lowered, a top quirk can be produced. A full round/bullnose for stair tre...

Self guided with low profile ball bearing guide and bearing fixing screw. For use in restrictive applications or within rebates of minimum 8mm. Down cut to prevent breakout on veneers. Dimensions: D=3/4 inch D=19.1 mm C=5/8 inch C=16 mm B=19.1 m...

Self-guiding trimmers with bearings mounted on end of cutter. For trimming plastic or plywood overlay. For copy profiling, use the bearing to follow a template or base edge of board. An approximate 3mm overlap should be left before copy profili...

Self-guiding trimmers with bearings mounted on end of cutter. For trimming plastic or plywood overlay. For copy profiling, use the bearing to follow a template or base edge of board. An approximate 3mm overlap should be left before copy profili...

Self-guiding trimmers with bearings mounted on end of cutter. For trimming plastic or plywood overlay. For copy profiling, use the bearing to follow a template or base edge of board. An approximate 3mm overlap should be left before copy profilin...

Self-guiding trimmers with bearings mounted on end of cutter. For trimming plastic or plywood overlay. For copy profiling, use the bearing to follow a template or base edge of board. An approximate 3mm overlap should be left before copy profili...

Self-guiding trimmers with bearings mounted on end of cutter. For trimming plastic or plywood overlay. For copy profiling, use the bearing to follow a template or base edge of board. A maximum of 3mm overlap should be left before copy profiling....

With bearing guided ogees, change profile by using a larger bearing and vary the depth. Dimensions: D=34.9 mm C=20 mm B=9.5 mm B2=12.7 mm R=6.3 mm OL=58 mm Shank Diameter=1/4 inch Shank Diameter: 1/4 Diameter Metric: 34.9 Cut Length Metric: 20 O...