|
|
Trend |
| TREND HM/SHEAR HAND MITRE SHEAR |
Product Code: HM/SHEAR With 45 degree angled wings.
For perfect mitre cuts of seals, mouldings, beadings and weatherseals.
Can be used to cut mouldings at 90 degrees up to 10mm thick.
For battens at 45 degrees the maximum thickness is 15mm and 35mm wide.
Left and right h...
|
| TREND INS/P6/10 INSERT PLASTICS M6 (10) |
Product Code: INS/P6/10 Threaded inserts for fixings in plastic.
Threaded inserts have enlarged flange ends to prevent them from 'pulling out' after continual usage.
The inserts need to be located from the underneath.
M6 inserts have slot on base and M8 inserts have slo...
|
| TREND INS/P6/50 INSERT PLASTICS M6 (50) |
Product Code: INS/P6/50 Threaded inserts for fixings in plastic.
Threaded inserts have enlarged flange ends to prevent them from 'pulling out' after continual usage.
The inserts need to be located from the underneath.
M6 inserts have slot on base and M8 inserts have slo...
|
| TREND INS/P8/10 INSERT PLASTICS M8 (10) |
Product Code: INS/P8/10 Threaded inserts for fixings in plastic.
Threaded inserts have enlarged flange ends to prevent them from 'pulling out' after continual usage.
The inserts need to be located from the underneath.
M6 inserts have slot on base and M8 inserts h...
|
| TREND INS/W6/10 INSERT FOR WOOD M6 10 |
Product Code: INS/W6/10 Threaded inserts for fixings in woods, man-made boards and fibre board e.g MDF.
Threaded inserts have enlarged flange ends to prevent them from 'pulling out' after continual usage.
The inserts need to be located from the underneath.
Dimensions:
...
|
| TREND INS/W6/50 INSERT FOR WOOD M6 50 |
Product Code: INS/W6/50 Threaded inserts for fixings in woods, man-made boards and fibre board e.g MDF.
Threaded inserts have enlarged flange ends to prevent them from 'pulling out' after continual usage.
The inserts need to be located from the underneath.
Dimensions:
...
|
| TREND INS/W8/10 INSERT FOR WOOD M8 10 |
Product Code: INS/W8/10 Threaded inserts for fixings in woods, man-made boards and fibre board e.g MDF.
Threaded inserts have enlarged flange ends to prevent them from 'pulling out' after continual usage.
The inserts need to be located from the underneath.
Dimensions:
...
|
| TREND INS/W8/50 INSERT FOR WOOD M8 50 |
Product Code: INS/W8/50 Threaded inserts for fixings in woods, man-made boards and fibre board e.g MDF.
Threaded inserts have enlarged flange ends to prevent them from 'pulling out' after continual usage.
The inserts need to be located from the underneath.
Dimensions:
...
|
| TREND JB/T101B JIGSAW BLADE 100X2.5MM CV 5PK |
Product Code: JB/T101B Trend Professional Jigsaw Blade - Upcut for clean face finish, pack of 5
100mm long blade with 10TPI (Teeth Per Inch) upcut profile for the cleanest of finishes on the face of the work.
Suitable for materials from 4mm to 30mm thick, ideal for crosscu...
|
| TREND JB/T101BR JIGSAW BLADE 100X2.5MM CV DC 5PK |
Product Code: JB/T101BR Trend Professional Jigsaw Blade - Down cut for fine finish, pack of 5
100mm long blade with 10TPI (Teeth Per Inch) down cut profile for fine cuts on timber and sheet materials.
Suitable for materials from 4mm to 30mm thick, ideal for crosscutting and...
|
| TREND JB/T111C JIGSAW BLADE 100X3MM CV 5PK |
Product Code: JB/T111C Trend Professional jigsaw blades five pack.
Universal T-shank.
Manufactured to the highest standards from high alloyed Chrome-Vanadium Steel (CV), perfect for use on softer materials.
Up-cut, milled, alternate set. The wood grain is ripped and the sa...
|
| TREND JB/T119B JIGSAW BLADE 75X2MM CV 5PK |
Product Code: JB/T119B Trend Professional Jigsaw Blade - For plastics and acrylics, pack of 5
75mm long blade with 12TPI (Teeth Per Inch) wavy set profile for sheet materials
55mm cut length, suitable for materials from 4mm to 30mm thick.
Suitable for hard and soft woods a...
|
| TREND JB/T144D JIGSAW BLADE 100X4MM CV 5PK |
Product Code: JB/T144D Trend Professional jigsaw blades five pack.
Universal T-shank.
Manufactured to the highest standards from high alloyed Chrome-Vanadium Steel (CV), perfect for use on softer materials.
Up-cut, cross-ground set. The angular sloped tooth cuts the wood g...
|
| TREND KB11/M/6 LEVER M6X30 1 OFF |
Product Code: KB11/M/6 Reinforced plastic lift and lock ratchet system.
Has steel stud.
Suitable when lever turning angle is limited.
Dimensions:
Thread=M6
Thread Length=30 mm
H=28 mm
D=42 mm
Diameter Metric: 42
Diameter 2 Metric: M6
Cut Length Metric: 30...
|
| TREND KB5/M/6 LOBE KNOB M6X20 2 OFF |
Product Code: KB5/M/6 Reinforced plastic. Has steel stud. Suitable when a strong clamping action is required.
Dimensions:
Thread=M6
Thread length=20 mm
H=23 mm
D=32 mm
Pack of 2
Diameter Metric: 32
Diameter 2 Metric: M6
Cut Length Metric: 20...
|
| TREND KWJ/PIN/4 KWJ900 PIN PACK 4 10MM |
Product Code: KWJ/PIN/4 Trend Location Pins - For Trend KWJ700 and KWJ900 Worktop Jigs. Pack of 4.
Set of four accurately machined replacement plastic location pins for the Trend KWJ700 and KWJ900 jigs.
Replacement pins to ensure the Trend Jigs continue offering professiona...
|
| TREND LOCK/JIG LOCK JIG |
Product Code: LOCK/JIG Contractor jig with interchangeable templates for use with a plunge router to cut the mortise & face-plate recess for popular door locks.
For most common sash mortises & dead locks, with up to 3 inch deep mortises & a 7/8 inch or 1 inch face-plate....
|
| TREND LOCK/JIG/A LOCK JIG LARGE |
Product Code: LOCK/JIG/A Contractor jig with interchangeable templates for use with a plunge router to cut the mortise & face-plate for larger locks quickly & accurately.
Suitable for DDA (Disabilty Discrimination Act) lock size.
20mm x 235mm radius end face plate, 24mm x 2...
|
| TREND M/P2P01 POINT TO POINT UP TO 600MM |
Product Code: M/P2P01 Trend Point to Point - For accurate marking of equal spaces.
Marks up equidistant positions across the width or length of any board from 85mm to 710mm quickly and accurately.
7 individual marking positions allows any workpiece to be marked in 2, 3, 4...
|
| TREND M/PB01 PERFECT BUTT SCRIBING TOOL |
Product Code: M/PB01 Trend Perfect Butt Scribing Tool - for fast accurate scribing work.
Multiple diameter scribing wheels allows fast scribe marking across both narrow and wider gaps. Also ideal for template making for spiling work.
5 different scribing diameter options...
|
| TREND MS/PRO MULTISCRIBE PRO |
Product Code: MS/PRO Trend Multiscribe Pro - Multi-function scribing tool
With its 15 functions, the Trend Multiscribe Pro is the Swiss Army Knife of marking, scribing and much more.
Scribes internal and external curves, marks parallel lines with fast, easy adjustable ba...
|
| TREND PB/28 PLANER BLADE SET 75.5X5.5X1.1MM TC |
Product Code: PB/28 Trend solid carbide planer blades are manufactured from high grade carbide and are supplied in pairs.
Precision ground with two cutting edges and reversible for extended life.
Two cutting edges and are reversible for twice the life
Solid Carbide ST...
|
| TREND PB/CK/119 PLANER BLADE CONVERSION |
Product Code: PB/CK/119 Contains a pair of plates to allow the PB/29 blades to be fitted into the planer cutter block for certain Makita, Hitachi and Kango planers.
Required for following:-
Hitachi F20, FU20
Makita M102, 1900, 1900B, 1901, 1125, 1100, 1923B, 1923BD
Ryobi L...
|
| TREND PC/10/M PANEL BUTT CONNECTORS 10PK METAL |
Product Code: PC/10/M Panel bolt connectors to connect worktop joint together.
Requires 10mm A/F spanner to tighten.
Pack of 10
Dimensions:
OL=150 mm
Type Grade=metal
Pack Quantity=10 pack
Overall Length Metric: 150...
|
| TREND PH/7X30/500C POCKET HOLE S/T SCW NO7X30 COARSE |
Product Code: PH/7X30/500C Square drive, self-tapping, solid steel wood screws coated with Zinc to protect against rusting, ideal for a variety of indoor projects. 30mm length coarse thread to suit 19mm softwood, plywood and particle board. Designed for use with Pocket Hole Ji...
|
|
|
Basket 0 items - £0.00
